Balun - A Twinax - to RJ45 adapter.
Pins 4 & 5 Active.Allows a
Twinax
signal to run over a CAT3 or CAT5 Cable. Good for distances of
up to 2000 to 2500 feet on a CAT5 cable. Not restricted to the 300
foot limitation of an Ethernet Signal. One
balun is required for each
Twinax device that is to be connected to a Twinax-to-RJ45
Active Star Panel.
Active Star Hub - A Twinax-to-RJ45 hub that allows
a
Twinax signalto run over a CAT3 or CAT5Cable.
The Hub
allows each of the 7 Twinax Addresses of a Twinax Host Port to be
connected to individually with a CAT5 cable in the same manner Ethernet
PCs are connected to an Ethernet Switch or Hub. Good for distances of up
to 2000 to 2500 feet on a CAT5 cable. Not restricted to the 300
foot limitation of an Ethernet Signal. One balun is required for each
Twinax device that is to beconnected to aTwinax-to-RJ45 Active Star Panel.
$ 450.00
ea.
CABLE-TWBRICK4
4-Port Twinax "Brick" - This
item is connected to the Twinax Workstation Controller of smaller
iSeries, AS/400 or S/36, as well as Twinax Remote Controllers such as
the IBM 5494 or the Perle 494e and 594e. You can connect up to 4
Twinax Cables or Baluns to this. If the AS/400 or Remote
Controller has a 4-port brick it will support up to a total of 28 Twinax
device addresses.
Call 800-597-2525
for Pricing & Availability
CABLE-TWBRICK8
8-Port Twinax "Brick" - This
item is connected to the Twinax Workstation Controller of the System i,
i5, iSeries, AS/400 or S/36. you can connect up to 8 Twinax Cables
or Baluns to this. Each Twinax Workstation Controller supports up
to a total of 40 Twinax device addresses.
Call 800-597-2525
for Pricing & Availability
CABLE-TWINAX##
(## is length
of cable)
Standard Twinax Cable - Allows "Daisy Chaining" from
one device to the next. Highly resistant to outside electrical
interference. Good for distances up to 5000 feet. You can
combine two standard Twinax cables together to get a longer length cable
by connecting them with a Twinax Female/Female Connector described
below.
Call 800-597-2525
for Pricing & Availability
CABLE-TWINAXEND
Twinax Cable Ends - Each end of a standard
Twinax cable has two
male connectors with two pins that connects to a female Twinax connector
that is either on an AS/400 or S/36 Twinax Workstation Controller,
Twinax ports on Remote Controllers, or the Host In port on an Twinax-to-RJ45
Active Star Panel. You can combine two standard Twinax
cables together to get a longer length cable by connecting them with a
Twinax Female/Female Connector described directly below.
Call 800-597-2525
for Pricing & Availability
CABLE-TWINAXFF
Twinax Female/Female Connector - Used to join two standard male
end Twinax cables together to increase length. Also used to
convert a male end of a cable to a female end to allow the attachment of
a Balun when a need exist to convert from standard Twinax cable to
RJ45. This is required when using Twinax star panels or hubs
that have female RJ45 ports and the existing cable runs are standard
Twinax cable.
$ 18.00 ea.
Twinax Signal- A
Twinax signal is the signal generated from
the Twinax port of an IBM AS400, iSeries, S/36, or remote controllers
that is sent over cabling to run a Twinax display station, Twinax
printer or other Twinax peripheral device. A Twinax signal can be
transmitted over a standard Twinax cable, CAT3 or CAT5 cables when
equipped with Baluns at each end of the cable, or over a fiber optic
cable when using the appropriate
Twinax-to-Fiber Optic Converter or
Twinax-to-Fiber Optic Multiplexor.
